Veneer Rotary Peeling Lathe-manufacture,factory,supplier from China

The demand for wood veneer dryer is increasing year by year,and it has been recognized and purchased by consumers.Traditional natural air-dried wood is prone to problems such as deformation and cracking.The use of wood dryer equipment can effectively solve this problem.The cost of dryer equipment is high, so basic maintenance needs to be done in the later use process,such as the ground,ventilation system, gate,instrument,heating system and debugging system,etc.The specific operations are as follows:1.The floor of the wood dryer equipment should be kept clean and tidy,and the debris should be c

In the stage you are catching up with a wide range of development, the lack of supply will affect the pace of industrial progress, rotary drying machine equipment manufacturing is a strategic industry in the national economy, the equipment level is equipped with a strong level, the country is strong, "a Wenbin" has many favorable elements for the future development of our country equipped with manufacturing operations, the domestic market potential is huge, rich resources. Money, rich human resources, the key is our approach and how to make better use of it.

Rotary cutting veneer dryer equipment has the characteristics of fast and monotonous, good uniformity, high energy efficiency ratio, small footprint, no environmental pollution, etc., can be widely used in various wood drying treatment. Equipped with infrared temperature measurement, low noise transmission system, active loading and unloading system. GMP manufacturing standards, microwave leakage is less than 1mw/㎡, strict implementation of relevant safety standards.

Faults of the board dryer are as follows: 1. Failure analysis of rotary granulator: the main engine current is unstable. Production reasons: uneven feed, main motor bearing damage or poor lubrication, no heating. Faulty heater or incorrect phase, incorrect screw adjusting pad, component interference. Treatment method: Troubleshooting, check the feeder, replace the bearing if necessary. Repair the main motor and replace the heater if necessary. Check whether each heater is working properly, pull out the screws to check the interference of the screws, and check the adjustment pad. 2.

Wood veneer is required to be dried in the veneer dryer to remove the moisture content present in it. Moisture content in wood veneer can cause several problems such as warping, cracking, splitting, and decay of the wood, which can lead to a reduction in the quality and value of the veneer.During the veneer manufacturing process, the logs are first peeled into veneer sheets using a lathe or a slicer. These veneer sheets are then sorted, graded, and stacked for drying.

The rotary veneer dryer is used for drying wood, which has the advantages of energy saving, reliability, short cycle, high quality and low cost. Widely used in all kinds of wood processing enterprises, especially suitable for wood products export enterprises. HGG series drying equipment, during normal operation, the fuel is fully burned in the combustion room, and the heat exchange system generates high temperature air.

The four deck veneer dryer purchased by myanmar factory is used to dry rubber wood. The customer gives good feedback. It is used with the biomass burner.The biomass burner which as the heat source can provide high temperature to the dryer to make sure the sufficient heat impinged on the wet veneer in an efficient manner. At the same time, the tree bark from debarker and waste veneer from peeling lathe were burned as the fuel directly, which solved the waste accumulation in the veneer plywood making factory.

It is understood that the rotary veneer dryer is a continuous boring equipment for mass production, which is used for the boring of sheet, strip, granular and some paste materials with good air permeability. It is especially suitable for high moisture content and heat sensitive materials such as traditional Chinese medicine pieces. It has the advantages of high drying rate, high evaporation intensity and good product quality. According to the different structure, the mesh belt dryer can be divided into many types.

Shine roller veneer dryer machine finished the installation in Jiangsu Province. The 2deck veneer dryer was ready for the test running. When the veneer is peeled from the veneer peeling lathe, we will start the test running on the core veneer roller dryer and conduct the training on the workers of the user's factory.  

1. Multi-band automatic temperature control, high temperature alarm, humidification, moisture drainage, punctual switching machine, suitable for wood secondary drying, balance wood moisture content.2. Fast heating, uniform heating, less heat loss, can be combined disassembly, easy to move, suitable for leasing plant and wood processing enterprises.3. Diesel-electric dual use, concave value electricity at night, low cost; Burn wood by day, low price, kill two birds with one stone.